TAVOR SAR Conversion Kit (9mm Para)
|
|
TAVOR SAR or X95 556NATO Bolt (in-house conversion service)
|
|
TAVOR SAR Conversion Kit (556NATO)
|
List Price: $899.99 Our Price: $749.99
|
|
|
Our Price: $109.99 Setup Cost: $30.00
|
|
|
Our Price: $899.99 Sale Price: $799.99
|
|
|
|
|
|
IWI TAVOR SAR Conversion Kit converts an existing 5.56 rifle into a 9mm.
Includes all the parts needed for the 9mm conversion, one 32 round magazine**, and a barrel lock wrench.
9mm Parabellum conversion kit with a Cold Hammer Forged 17" barrel**, 1:10 twist, CrMoV steel
** Know your local laws! Certain items in the kit are restricted in some areas. We can remove the hi-cap mag, if required by your state (put a note in the comments section when checking out...)
|
IWI TAVOR SAR or X95 Bolt Conversion for 5.56NATO or 300BLK! Bullpup Armory is a CERTIFIED IWI TAVOR ARMORER! Send us your TAVOR SAR or X95, and we'll switch the ejection to the other side per IWI specs. When you get your rifle back, you'll have the new configuration, plus the original bolt, for when you need to switch back to the original configuration. Fastest turnaround times in the industry!
** IWI-US requires the Tavor barrel and new bolt to be headspaced by an IWI certified gun-smith/armorer **
* Bolts are not available individually without purchasing a barrel set, or sending your Tavor to us for the install. (IWI Policy)
|
IWI TAVOR SAR Conversion Kit converts an existing 9mm rifle into a 5.56.
Includes all the parts needed for the conversion, 5.56 barrel, bolt/bolt-carrier, ejection port frame & shell deflector, one 30 round magazine**, and a barrel lock wrench. 5.56 NATO conversion kit with a Cold Hammer Forged 16.5" barrel**, 1:7 twist, CrMoV steel. Longer muzzle devices sold separately.
** Know your local laws! Certain items in the kit are restricted in some areas. We can remove the hi-cap mag, if required by your state (put a note in the comments section when checking out...)
|
|
Percival Armaments - Tavor and X-95 Shell Deflector - Angled and Contoured
|
|
Percival Armaments - Tavor and X-95 Shell Deflector - angled face for the 9mm
|
|
Percival Armaments - Tavor SAR Dust Protection Plate
|
|
|
|
|
|
|
Percival Armaments makes improvements
to the tactical shooting experience of the Tavor SAR and X95 with the redesign of
the Shell Deflector.
For the 5.56 models. Shooting .223 or “light loads”
through the Tavor SAR or X95 can cause the ejecting case to skip past the factory
shell deflector, and potentially hit the operator in the face or body (if
shooting from the ejection-port side).
The simple replacement of the upgraded Percival
Armaments Shell Deflector can help alleviate the issues, through an angled
deflector face, and taller body.
Select from RIGHT SIDE EJECTION or LEFT SIDE EJECTION.
Made in the USA!
|
Percival Armaments makes improvements
to the tactical shooting experience of the Tavor and X95 with the redesign of
the 9mm Shell Deflector.
Shooting “light loads”
through the Tavor or X95 can cause the ejecting case to skip past the factory
shell deflector, and potentially hit the operator in the face or body (if
shooting from the ejection-port side).
The simple replacement of the upgraded Percival
Armaments Shell Deflector can help alleviate the issues, through an angled
deflector face, and taller body.
Select from RIGHT SIDE EJECTION or LEFT SIDE EJECTION.
Made in the USA!
|
Percival Armaments makes improvements
to the tactical shooting experience of the Tavor SAR with the redesign of
the Dust Protection Plate.
Adding an after-market charging handle/rod to both sides of the Tavor SAR is now possible while keeping the function of a dust protection plate as part of the gas system. A Barrel Lock Wrench is needed to make this upgrade. Made in the USA!
|
|
Percival Armaments - Tavor and X-95 Shell Deflector - Angled and Contoured - 300 AAC Blackout
|
|
TAVOR SAR 556 NATO Barrel & Bolt Kit
|
|
Bayonet Lug mounted Picatinny Rail
|
|
Our Price: $449.99 Sale Price: $399.99
|
|
|
|
|
|
|
Percival Armaments makes improvements
to the tactical shooting experience of the Tavor SAR and X95 with the redesign of
the Shell Deflector.
For the 300 AAC Blackout models. Shooting sub-sonic or “light loads”
through the Tavor SAR or X95 can cause the ejecting case to skip past the factory
shell deflector, and potentially hit the operator in the face or body (if
shooting from the ejection-port side).
The simple replacement of the upgraded Percival
Armaments Shell Deflector can help alleviate the issues, through an angled
deflector face, and taller body.
Select from RIGHT SIDE EJECTION or LEFT SIDE EJECTION.
Made in the USA!
|
This IWI factory barrel and bolt kit comes head spaced from the factory and should be used together. Be sure to replace your bolt when replacing your barrel. Please check your local and state laws before assembling your Tavor® SAR with your new Barrel & Bolt Kit.
** Know your local laws! Certain items are restricted in some areas.
|
Transforms the bayonet lug into a Picatinny rail section.
Allows the addition of flashlight, laser and other mounts No Gunsmithing
Lock-tite is suggested for the set-screw(s).
|
|
Bullpup Armory - TAVOR and X-95 Barrel Lock Wrench
|
|
ShootingSight TAV-TOOL - multi-tool specifically for the Tavor® X95 and SAR
|
|
IWI TAVOR Official Gunsmith Bench Mat
|
|
|
|
|
|
|
IWI TAVOR SAR & X-95 Barrel Lock Wrench. Made from 17-4PH Stainless, with a rubberized handle. Hardened strength, corrosion resistant, and a comfortable grip that won't scratch your Tavor!
Always refer to the IWI Owners Manual when disassembling-reassembling a Tavor/X-95.
Made in the USA!
|
ShootingSight LLC has developed a customized multi-tool specifically for the IWI Tavor®. Contains the critical tools to maintain the rifle, including:
Barrel Removal Tool, Screwdriver to adjust the front sight windage, Phillips Screwdriver to remove handguards, Hex Wrenches to remove top and side rails, Awl to lift out spring pin in swivel, Hex Bit Socket to allow customized tips for any optics (hex tips available at most hardware stores). NOW INCLUDES A 3mm HEX BIT FOR THE X95!
Choose your PALS/MOLLE POUCH in Black,Tan, or ODG
Tav-Tool made in the USA!
|
Gunsmith/Armorers bench mat with Tavor® SAR exploded view diagram and a list of parts. The
soft polyester-cloth top will protect your gun from scratches. The non-slip
neoprene rubber back will prevent chemicals and oils from damaging your
workspace.
12" x 36" x 1/8" thick
|
|
Bullpup Armory 4"x2" PVC Patch with Velcro Backing
|
|
|
|
|
|
|
The Bullpup Armory logo in 3D!! The textures and colors of this new patch are outstanding! This patch matches a full range of "tactical" colors: tans, browns, greens, greys, and blacks. A "shout-out" to MilSpecMonkey for making great patches for the Bullpup fan!
Bullpup Armory PVC Rubber Patch is 4" wide x 2" tall, with hook-velcro backing mating easily with any loop-velcro surface.
Made in the USA!
|
|